Prologue
i use with my fatsharks on a 100mm brushed setup. Color saturation is good and range is on par with all the 25mw transmitters. The weight (or lack there of) is what sold me on this. I'm not aware of anything lighter on the market, especially in this price range. I was going to use an eachine tx03 but it was a bit too large for my application and double the weight. I couldn't be happier with the results. I attached a video of a flight using this camera on a kingkong q100 frame (still learning so don't judge my flying! ). The Best micro aio camera fpv transmitter as-of ( Dec 2019 ) | Sinopine-Surveilance Systems Review Extra Wolfwhoop WT05 Micro AIO 600TVL Camera Only 3.4g 5.8GHz 25mW FPV Transmitter with Dipole Brass Antenna Combo for FPV Quadcopter Drone Power by 1s lipo battery. Easy installation for racing drone, only 3. 4g. Button contro l instead of switches to change channels. The aio camera combo is perfect for ultra micro drone. All in one vtx + camera + antenna, plug and play, ready to fly .
Wolfwhoop Wt05 Micro Aio 600tvl Camera Only 3.4g 5.8ghz 25mw Fpv Transmitter With Dipole Brass Antenna Combo For Fpv Quadcopter Drone Review (wt05)
This wolfwhoop wt05 micro aio 600tvl camera works well. I paid $16. 66 and have been happy, thus far. It weighs in at 3. 5g. I soldered a jst 1. 25mm connector on the top of the fc above the battery connector. Placing the cam on the fc of my furibee f36 on a piece of foam that i cut from the cam packaging and a rubber band makes mounting/removing easy. This cam consumes 230ma and does get warm. It also requires a fair amount more throttle for the f36 to operate. I've tried the stock 31mm props, and the modded 2-blade props-with and without the camera; both scenarios are better with the 2-bladed prop setup. With 260ma batt, i get just over 3 minutes flight time with this cam as long as i'm not punching it and sagging the voltage towards the end of the run. Interestingly, i get the same 3 minute run time with the 220ma batts and better agility/performance due to the lighter weight-i guess 220ma are the sweet spot in terms of weight vs. Mah. Picture quality is good, and distance is beyond my remote while using a small dipole antenna. The blue/red leds and the long/short push buttons are easy to use with this vtx. However, the manual that came with the wt05 lists 48 channels and how the leds correspond; but, doesn't list the combos for race channels. I use this while recording on my galaxy s5 using and eachine rotg02. -R. Susana
- Order: Toy
- Brand: Wolfwhoop
- Product Dimensions:
Weight: 0.1 pounds - Manufacturer: Sinopine
- Model: WT05
- MPN: WT05
- Quantity: 1
- Part/Serial Number: WT05
- Sub-Type: Photography
- Category: SURVEILANCE SYSTEMS
micro aio 600tvl camera 3.4g 5.8ghz 25mw fpv transmitter dipole brass antenna combo fpv quadcopter Photography, description : the aio camera combo is perfect for ultra micro drone. it is a combination of a fpv camera, a transmitter and an antenna. it includes everything into a single unit no bigger than one dollar coin. micro size and light weight only 3. 4g specification: frequency 5. 8ghz 6 bands 48 channels, with raceband: 5658-5917mhz output power 25mw input voltage 3. 3v-5. 5v current consumption 280ma(typ) camera resolution 600tvl field of view 120 video format ntsc antenna: dipole brass antenna size: 15x 12. 5mm(lx w) weight: 3. 4g package included: 1 x wt05 aio fpv camera (with cable) 1 x user manual 1 x cable Wolfwhoop Wt05 Transmitter Antenna Quadcopter (WT05-Wolfwhoop).
Wolfwhoop Wt05 Transmitter Antenna Quadcopter Photography
Wolfwhoop WT05 Micro AIO 600TVL Camera Only 3.4g 5.8GHz 25mW FPV Transmitter with Dipole Brass Antenna Combo for FPV Quadcopter Drone (Switch to Mobile/Desktop Version)
Works great, the range doesn't seem to be that far, but for a indoor tiny whoop it works great. . Update: furibee q95 camera died, so i through this one on it. So much better outdoors. I tapped the video feed by tapping the bottom left wire, when looking at the camera from the front, like in the image. I haven't tested the range outdoors but it might not be that far. Yellow wire in the image is the video out and the white one is the video in. . For those with the furibee q95, to clean up the video, i also wired in the battery into the flight controller. I think it powers the on board bec of the flight controller, giving you more power to power all the 5v devices plugged into it. You will have to remove the buzzer/led board, otherwise it will short and fry your camera along with the led board, i figured it out the hard way. Remember remove the buzzer/led board when you wire in the battery to the flight controller. . Now to fpv.
Wolfwhoop Wt05 Micro Aio 600tvl Camera 3.4g 5.8ghz 25mw Fpv Transmitter Dipole Brass Antenna Combo Fpv Quadcopter DroneClick to see Notice
Wolfwhoop Wt05 Transmitter Antenna Quadcopter (Surveilance Systems)"Lets start off with the admission that i am extremely hard on my tiny whoops! the kids and i race our whoops around the house non-stop. As anyone who is an avid pico-drone racer will tell you this type of flying comes with a lot of crash's. And as such, i have a lot of experience with many different camera vtx combos. I have been hugely impressed by the wt05. It has a great picture for a cmos camera, and the range is exactly what i would expect out of a 25mw vtx. And did i mention that the included dipole is tough? the entire camera can take some punishment. All this at a price that is less than half of some of the best camera's vtx combos on the market. . Give the wt05 a go, i think you will be impressed."Wolfwhoop WR832 5.8GHz 40CH Wireless FPV Receiver Racing Drone Multicopter
This 40 channel 5. 8ghz av wireless receiver has high power, designed for all kinds of drones. Specification: power supply: dc 12v working frequency: 5. 8ghz sensitivity: 90 dbm type standard: ntsc/pal consumption current: 200ma, max receiver connector: rp sma female antenna connector: rp sma male available channel: 40ch antenna gain: 2dbi audio carrier: 6. 5mhz audio output level: 1. 0 vp-p typ 10 k ohm antenna impedance: 50 ohm antenna input impedance: 50 ohm typ video impedance: 75 ohm video format : ntsc/pal video output level: 1. 0 vp-p typ 75 ohm dimension: 80x65x15mm weight: 85g dimension (lxwxh): 3. 15x2. 56x0. 59 inches package: 1 x wr832 5. 8ghz 40ch fpv receiver 1 x antenna 1 x power cable 1 x av cable 1 x user manual notice: please get a 12v lipo battery for the receiver. We do not suggest over-voltage battery or car battery. Please plug antenna before powering up, otherwise static electricity will damage the product. Wolfwhoop is never good at brand promotion, the only thing we do is manufacturering. Wolfwhoop promise that every piece of product you bought from our store is made by wolfwhoop self-owned factory. Keep real, keep factory direct. Save money, fly better. Please feel free to contact us if you have new ideas for fpv products.
Wolfwhoop-WR832-Wireless-Receiver-Multicopter
| WOLFWHOOP WR832 5.8GHZ 40CH WIRELESS FPV RECEIVER RACING DRONE MULTICOPTER Features | |
|---|---|
| Brand : | wolfwhoop |
| Weight : | 0.26 pounds |
| Model : | WR832 |
| Quantity : | 1 |
| Order click here : | normally ships in 24 hours |
| Photography : | Best Surveilance Systems (wolfwhoop product review) for Wolfwhoop WR832 5.8GHz 40CH Wireless FPV Receiver Racing Drone Multicopter available as-of ( Dec 2019 ) |
| Price : | $16.66 |
| |
FPV 5.8GHz Receiver, 150CH UVC Video Downlink OTG Receiver ONLY OTG UVC Android Mobile
Operation instructions: 1. For android phone: install suitable app (go-fpv, easycap & uvc player(fpviewer), pocketfpv or fpvdroid) for windows xp or win7/8, download "amcap" for windows 10, simply open it from "camera" 2. Calibrate the max and min fpv signal value range by pressing and holding the function button whilst powering the receiver (i. E. Plugging it in). 3. With the transmitter powered, press and hold the function button for 3s and this searches the frequency automatically. 4. Press the function button for 1s to enable osd. 5. App download: ; your device must android system with otg functi ; supporting phone list: here's the phone list support this receiver that we have tested. Please read it carefully before order. Please note: do not fit for samsung galaxy j5 prime) for samsung: s3(i9300, i9308) s4(i9500, i9507v, i9508, s5, s6, s6 for edge+, fors7edge, note3, note4, note5, a5100, a8000, on7, p600, n7100, n5100, tab s2 etc. For oppo: a31, a31c, a33, a51, a53, a33m, a51, a53, a5m, n3, find7, r7005, r7007, 3007, r2017, r8000, r8205, r8207, r7sm, r7 plus, r9 plus, etc. For xiaomi: for xiaomi 3, for xiaomi 4, for xiaomi 4c, for xiaomi5, for xiaomi pad, for xiaomi red note, for xiaomi red note3, etc. For huawei: mate8, c199, honor8 for lg: gpro2, g3, nexus5, l24, gpad8. 3, etc. For motorola: xpro, nexus6, moto e, mz617, etc. For sony: z1, z2, z3, c3, sgp321, etc. Specifications: color: black size: 61*33*10 mm channel: 150ch sensitivity: -90dbm connector: rp-sma resolution: 640 * 480 30fps working current: 200ma/5v operating temperature: -10 60 frequency range: 5645 5945mhz power supply: 5v(by smart phone) packing list: 1 x 5. 8g 150ch mobile receiver 1 x sma-antenna 1 x usb cable
5-8GHz-Receiver-Downlink-Android-Mobile
| FPV 5.8GHZ RECEIVER, 150CH UVC VIDEO DOWNLINK OTG RECEIVER ONLY OTG UVC ANDROID MOBILE Benefit | |
|---|---|
| Brand : | otryad |
| Color : | Black |
| Size : | Rotg01 |
| |
| Price : | $23.70 |
| Model : | HOMISH111-B |
| Order click here : | normally ships in 24 hours |
| Toy : | Best Toys And Games (otryad product review) for FPV 5.8GHz Receiver, 150CH UVC Video Downlink OTG Receiver ONLY OTG UVC Android Mobile available as-of ( Dec 2019 ) |
Crazepony 4pcs 6x15mm Motor Speed: Insane 19000KV Blade Inductrix Tiny Whoop Micro JST 1.25 Plug Rubber Rings
Came quickly. A quick repair for my inductrix. The motors come with color coded wires for the ones that spin clockwise and the ones that spin counter-clockwise. You need to google what's all about as these come with no instructions.
Description: motor diameter: 6mm motor length: 15mm shaft diameter: 0. 8mm cable length: 56mm weight: 1. 8g each no load speed: 70000 15% rpm rated load speed: 40500 15% rpm motor wire: clockwise motor(with red blue), anti-clockwise motor(with black white) option: with 1. 25mm jst plug quantity: 4 pcs (2 cw and 2 ccw) work for blade inductrix, tiny whoop, nano qx etc bonus rubber rings package including 2 * cw motor 2 * ccw motor
Crazepony-4pcs-6x15mm-Motor-Speed
Crazepony 4pcs 6x15mm Motor Speed (43234 1372) FAQ.
I installed these motors as a replacement motors for my inductrix fpv pro which are supposed to be 19600 kv or at least i thought. When i looked for the original motors online, they were $40. 00. Obviously did not get them and instead got these at a great price. These are 19000kv but after break in, are more powerful than the original motors on the inductrix fpv pro. I love this motors but would like to see a higher kv version for a betaflight configurable board like the one on the pro where the throttle curve is fully configurable and it will do wonders! -Notice from U. Gilmore, Sheffield
Click to Show crazepony 4pcs 6x15mm motor speed (43234 1372) Details
Incredible little motors, turned my jjrc h36 into a speed demon. Definitely worth the cost for how cheap these motors are. Shipping was fast and packing kept the motors safe and clean. . Would definitely recommend these to anyone looking to speed up their micro quadcopter. Don't forget to get some better batteries though. The 230mah 30c batteries that crazepony also sells worked awesome for me, but you're going to have to modify the frame on an e010 or jjrc h36 to hold the smaller battery type
- J. BethanyYup, you can really tell the difference between these and the 17500kv motors. Or the "black" edition motors i bought from newbee. They work far better than expected and at half the price! awesome, can't say enough good things. What i do is connect all the motors to the board while the board is not on the frame, then i do one whole 3360 degree twist of the fc and it pulls all the motor wires close together for a nice, tight clean build and you dont have to fiddle with the rubber bands on the motors.
The motors, i ordered are very good and perhaps excellent for testing batteries. I was testing some 150mah batteries last night. In testing those batteries i guess i also put your motors to the test. . I have the motors on my furibee f36. I used all 6 batteries one right after another with no time to cool down. Well the result was after 35 minutes of continuous use the motors were barely warm, just as warm as my hand. To fly that long consecutively and not have hot motors with extended use is very good and only comes with quality products. Also the motors were well packaged and arrived on time. . Thank you crazypony for caring about your products and your customers. You have excellent costumer service. Also shipping was on time and the motors were well packaged.
P. Anonymous, Midi-Pyrenees
| CRAZEPONY 4PCS 6X15MM MOTOR SPEED: INSANE 19000KV BLADE INDUCTRIX TINY WHOOP MICRO JST 1.25 PLUG RUBBER RINGS Advantages | |
|---|---|
| Brand : | crazepony |
| Size : | Small |
| Weight : | 0.4 pounds |
| |
| Price : | $9.99 (was $19.99) |
| Model : | 43234-1372 |
| Quantity : | 1 |
| Order click here : | normally ships in 24 hours |
| Toy : | Best Hobbies (crazepony product review) for Crazepony 4pcs 6x15mm Motor Speed: Insane 19000KV Blade Inductrix Tiny Whoop Micro JST 1.25 Plug Rubber Rings available as-of ( Dec 2019 ) |
Crazepony 3pcs F04 FPV Camera Vacuum Plastic Mount Tiny Whoop Crazepony FPV Micro AIO Camera
3pcs f04 fpv camera vacuum plastic mount tiny whoop for crazepony fpv micro aio camera description: this is the perfect angle for both fast-forward flight as well as slow manuvering thru dense treetops. It is still low enough to look down between the ducts to drop thru small slots or gaps. This is a fpv camera mount /vtx mount for the f04 fpv camera. With very light weighs in at 1. 2g. Small size: 4. 7 * 4. 0 * 1. 5 cm. Holds the camera securely and eliminates the chance of tearing a smd component of the board with aggressive double sided tapes. All stock hardware is used, super simple installation. - package including 3 * f04 fpv camera vacuum plastic mount
Crazepony-Camera-Vacuum-Plastic-Mount
| CRAZEPONY 3PCS F04 FPV CAMERA VACUUM PLASTIC MOUNT TINY WHOOP CRAZEPONY FPV MICRO AIO CAMERA Pros | |
|---|---|
| Brand : | crazepony |
| Color : | As Shown |
| Size : | 3pcs Camera Mount |
| Weight : | 0.1 pounds |
| Model : | COMINU053704 |
| Quantity : | 1 |
| Order click here : | normally ships in 24 hours |
| Toy : | Best Hobbies (crazepony product review) for Crazepony 3pcs F04 FPV Camera Vacuum Plastic Mount Tiny Whoop Crazepony FPV Micro AIO Camera available as-of ( Dec 2019 ) |
| Price : | $6.99 |
| |
AKK A5 5.8Ghz 25mW FPV Transmitter 600TVL CMOS Micro Camera Support OSD Switchable Raceband for Quadcopter Drone Like Tiny Whoop Blade Inductrix
Specifications: output power: 25mw input power: 3. 3v-5. 0 v current consumption:3. 3v-5v, 350ma camera resolution: 600tvl range: 150m video system:ntsc mini illumination: 1 lux field of view: 120 viewing angle antenna: dipole brass antenna frequency: 5. 8ghz 5 bands 40 channels, with raceband: 5725-5875mhz vtx size: 19*14mm(l*w) camera size: 14*14mm(l*w) package included: 1x fpv transmitter with camera 1x cable 1x manual
AKK-Transmitter-Switchable-Raceband-Quadcopter
| AKK A5 5.8GHZ 25MW FPV TRANSMITTER 600TVL CMOS MICRO CAMERA SUPPORT OSD SWITCHABLE RACEBAND FOR QUADCOPTER DRONE LIKE TINY WHOOP BLADE INDUCTRIX Advantage | |
|---|---|
| Brand : | akk |
| Weight : | 0.1 pounds |
| Model : | K-A5 |
| Quantity : | 1 |
| Order click here : | normally ships in 24 hours |
| |
| Price : | $16.99 |
| Toy : | Best Hobbies (akk product review) for AKK A5 5.8Ghz 25mW FPV Transmitter 600TVL CMOS Micro Camera Support OSD Switchable Raceband for Quadcopter Drone Like Tiny Whoop Blade Inductrix available as-of ( Dec 2019 ) |
BETAFPV 8pcs 300mAh HV 1S Lipo Battery 30C 4.35V JST-PH 2.0 Powerwhoop Connector Tiny Whoop Blade Inductrix
Betafpv 8pcs 300mah hv 1s lipo battery 30c 3. 8v with jst-ph 2. 0 powerwhoop connector for tiny whoop blade inductrix micro mini drone specification: item: 300 mah hv 1s lipo battry capacity: 300mah size: 58mm*11mm*6mm continuous discharge rate: 30c weight: 7. 7g/pc flight time: 5'10' on beta65s (if we use 260mah battery, we can get 4'10' only on beta65s. ) caution: don't over-charge, or over-discharge batteries. Don't put it beside the high temperature condition. Don't throw it into fire. Don't throw it into water. Package including 8 * 300mah 1s lipo battery 30c 3. 8v with jst-ph 2. 0 powerwhoop connector
BETAFPV-Battery-Powerwhoop-Connector-Inductrix
| BETAFPV 8PCS 300MAH HV 1S LIPO BATTERY 30C 4.35V JST-PH 2.0 POWERWHOOP CONNECTOR TINY WHOOP BLADE INDUCTRIX Pros | |
|---|---|
| Brand : | betafpv |
| Color : | 300mAh HV |
| Weight : | 0.1 pounds |
| Model : | 00313297 |
| Quantity : | 1 |
| Order click here : | normally ships in 24 hours |
| Toy : | Best Battery (betafpv product review) for BETAFPV 8pcs 300mAh HV 1S Lipo Battery 30C 4.35V JST-PH 2.0 Powerwhoop Connector Tiny Whoop Blade Inductrix available as-of ( Dec 2019 ) |
| Price : | $26.99 |
| |
BETAFPV 10pcs Upgraded Tiny Whoop JST-PH 2.0 Power Whoop Female Connector Cable 55mm Blade Inductrix
Specification: connector : female jst-ph 2. 0, aka powerwhoop female length: 55mm (not include the plug) wire: 24awg package including 10 * jst-ph 2. 0 female cable
BETAFPV-Upgraded-JST-PH-Connector-Inductrix
| BETAFPV 10PCS UPGRADED TINY WHOOP JST-PH 2.0 POWER WHOOP FEMALE CONNECTOR CABLE 55MM BLADE INDUCTRIX Advantages | |
|---|---|
| Brand : | betafpv |
| Weight : | 0.4 pounds |
| Model : | 00312657 |
| Order click here : | normally ships in 24 hours |
| Toy : | Best Toys And Games (betafpv product review) for BETAFPV 10pcs Upgraded Tiny Whoop JST-PH 2.0 Power Whoop Female Connector Cable 55mm Blade Inductrix available as-of ( Dec 2019 ) |
| Price : | $8.99 |
| |
4pcs 230mAh HV 1S Lipo Battery 30C 3.8V Tiny Whoop Blade Inductrix JST-PH 2.0 Connector
These work as advertised, but i question the rated capacity. Even when charged as hv they only seem to carry about a 210 mah capacity. Otherwise they work as described.
4pcs 230mah hv 1s lipo battery 30c 3. 8v for tiny whoop blade inductrix jst-ph 2. 0 connector features: item: hv 1s crazepony lipo battery rate: 30c dimension: 54mm * 12. 5mm * 6mm weight: 6. 3g/per unit capacity: 230mah in standard voltage, 250mah in high voltage the connector plug: jst-ph 2. 0 aka high current ultra micro, powerwhoop, mcpx this battery is lighter than the usual 230mah battery, and can be charged to either standard voltage (4. 2v, 230mah) or high voltage (4. 35v, 250ish mah). This is newly developed chemistry for a longer lifetime and safer charging situation. This battery will give you higher rpms (more power) and a considerably longer flight time. High density with great safety fits tiny whoop - package including 4 * 230mah hv 1s lipo battery 30c 3. 8v jst-ph 2. 0 connector
230mAh-Battery-Inductrix-JST-PH-Connector
Crazepony 230mah Battery Inductrix Connector (2143529fkrb6281) FAQ.
Batteries came with good packaging. They fit the stock tiny whoop frame just fine but the upgraded frames (with the foam piece) are a bit tight. One battery came damaged but customer support was very quick in resolving the issue with me. -Notice from O. Teresa, New Brunswick
Click to Show crazepony 230mah battery inductrix connector (2143529fkrb6281) Details
Another great buy from crazypony. I got these to run in my whoop build. Everything is running great. Charged up like normal, discharge seems solid since they don't get hot after flying. The plug they come with is a good replacement or upgrade to the 2. 0.
- N. MeyerIf you have a "tiny whoop" or anything of similar size, this is the absolute first upgrade you should make. The battery connector is such a bottleneck, and this fixes that while providing a light enough battery with enough c rating to see a huge difference. Flight times around the same as my 600mah blue pill battery, but the flights are snappier and i spend less time bouncing off the ground due to weight/battery sag. Will buy more!
So far my tiny whoop rebuild has seen flight times increase to 5:10 (mild flying and hovering) to 4:52 (aggressive speed runs with 180 turn around at each end). *note these can still be used as standard 1s lipo batteries if you don't have an hi voltage setting on your charger. I do wish the pigtail was just a few mm longer as it uses thicker cable which is slightly less flexible than the stock wire (which makes for a tighter time bending/connecting the battery and limits the distance you can extend the battery as a counter weight to the camera (if running a tiny whoop). I initially wanted to route mine from the top, but it came up short and couldn't connect the battery so i had to re-soldier to the bottom of the fc (original location). I've attached a couple of pics for reference.
D. Fabian, Colorado
| 4PCS 230MAH HV 1S LIPO BATTERY 30C 3.8V TINY WHOOP BLADE INDUCTRIX JST-PH 2.0 CONNECTOR Pros | |
|---|---|
| Price : | $12.99 |
| |
| Brand : | crazepony |
| Color : | 230mah 2.0 |
| Size : | small |
| Weight : | 0.1 pounds |
| Model : | 2143529FKRB6281 |
| Quantity : | 1 |
| Order click here : | normally ships in 24 hours |
| Toy : | Best Battery (crazepony product review) for 4pcs 230mAh HV 1S Lipo Battery 30C 3.8V Tiny Whoop Blade Inductrix JST-PH 2.0 Connector available as-of ( Dec 2019 ) |
Crazepony Mini Quadcopter Frame Kit Props Removal Tool Tiny Whoop Eachine E010 JJRC H36 Quadcopter
Mini quadcopter frame kit with props removal tool for tiny whoop eachine e010 jjrc h36 quadcopter description: frame wheelbase: 67mm material: pvc propeller color: red quantity: 1pc quadcopter frame, 8pcs 4-leaf red propellers, 2pcs foam battery compartment adaptors ( random color ) and1pcs removal tool usage: for tiny whoop, eachine e010 or jjrc h36 - package including 1 * micro quadcopter frame black 8 * 4-leaf red propellers 2 * foam battery compartment adaptors (random color) 1 * props removal tool
Crazepony-Quadcopter-Frame-Removal-Eachine
| CRAZEPONY MINI QUADCOPTER FRAME KIT PROPS REMOVAL TOOL TINY WHOOP EACHINE E010 JJRC H36 QUADCOPTER Benefits | |
|---|---|
| Price : | $9.99 |
| |
| Brand : | crazepony |
| Color : | Upgrade Version |
| Size : | Small |
| Weight : | 0.2 pounds |
| Model : | K154902D60M1281 |
| Order click here : | normally ships in 24 hours |
| Toy : | Best Toys And Games (crazepony product review) for Crazepony Mini Quadcopter Frame Kit Props Removal Tool Tiny Whoop Eachine E010 JJRC H36 Quadcopter available as-of ( Dec 2019 ) |
Upgrade 1S LiPo Battery USB 3.8V/4.35V Charger 6 Channel 1S LiHV Charger EMAX Tinyhawk Blade Inductrix Tiny Whoop Inductrix FPV Plus Battery Micro JST 1.25 JST-PH 2.0 mCX mCPX Connectors
1s lipo battery usb charger 3. 8v/4. 35v 6 channel 1s lihv charger tiny whoop blade inductrix micro jst 1. 25 jst-ph 2. 0 mcx mcpx connectors specifications: only support lihv 3. 8v/4. 35v 1s battery, not for 4. 20v 1s lipo battery support 0. 2a/0. 6a charge current by switch button usb power supply interface input range: 5v plusmn; 5% on 0. 5 2a, suggested 2. 4a charger plug: micro 1. 25 and jst-ph 2. 0 the 6 led lights indicate the charging state of the six channels independently, led solid indicates charging, led off indicates full charged. Battery charging termination voltage:li-hv type 4. 35v plusmn; 0. 5% product dimensions: 73x25x10mm product weight: 13g - package including 1 * 1s lipo battery usb charger 3. 8v/4. 35v lihv version
Upgrade-Battery-Tinyhawk-Inductrix-Connectors
| UPGRADE 1S LIPO BATTERY USB 3.8V/4.35V CHARGER 6 CHANNEL 1S LIHV CHARGER EMAX TINYHAWK BLADE INDUCTRIX TINY WHOOP INDUCTRIX FPV PLUS BATTERY MICRO JST 1.25 JST-PH 2.0 MCX MCPX CONNECTORS Benefit | |
|---|---|
| Price : | $8.59 (was $9.99) |
| |
| Brand : | crazepony |
| Color : | As Shown |
| Size : | XXS |
| Weight : | 0.3 pounds |
| Model : | W155801AMBSK281 |
| Order click here : | normally ships in 24 hours |
| Toy : | Best Home (crazepony product review) for Upgrade 1S LiPo Battery USB 3.8V/4.35V Charger 6 Channel 1S LiHV Charger EMAX Tinyhawk Blade Inductrix Tiny Whoop Inductrix FPV Plus Battery Micro JST 1.25 JST-PH 2.0 mCX mCPX Connectors available as-of ( Dec 2019 ) |
